If the vent is restricted, the steam will remain inside the dryer. You may notice steam on the door , or when opening the door. If your dryer has an electronic display, you may also see the display steaming over. Architectural wiring diagrams reveal the approximate areas and interconnections of receptacles, lighting, and permanent electrical services in a building. You must guarantee enclosing all wiring connections in appropriate electrical boxes or clamps.
Tools and Supplies You’ll Need to Hook Up Your Maytag® Steam Dryer
Ground wire must be connected to green ground connector. This dryer is equipped for use with Natural gas. It is certified by UL for use with propane gas with appropriate conversion. Use a new CSA International approved gas supply line. Does anyone know of a source for obsolete Maytag parts? Or does anyone have any idea of what I could do?
If lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint. See “Venting Requirements” in the Installation Instructions. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.
Like installing the power cord to your appliance, instructions for making the gas connection to your gas dryer may vary depending on the make and model. Refer to your product manual for model specific installation instructions. If you’re not experienced with electrical work, schedule a time with a licensed technician. Determine if you’ll use vent clamps or foil tape to secure the dryer venting to the dryer exhaust outlet and wall vent.
See “Electrical Requirements” in the “Gas Dryer Power Hookup” section. Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your dryer. For further information, please refer to the Quick Start Guide for service contact information. Replace inlet hose and hose screen after 5 years of use to reduce the risk of hose failure.
Step 6: Push dryer into place and check leveling
Use an elbow and a 3/8″ flare x 3/8″ NPT adapter fitting between the stainless steel gas connector and the dryer gas pipe, as needed, to prevent kinking. If local codes permit, use a new flexible stainless steel gas connector to connect your dryer to the rigid gas supply line. Use an elbow and a 3/8″ flare x 3/8″ NPT adapter fitting between the stainless steel gas connector and the dryer gas pipe, as needed to prevent kinking.
It should be at least five feet in length so you can move your dryer with relative ease. Strip 5″ of outer covering from the end of the cable, leaving bare ground wire in its place. Cut 1½” each from the remaining three wires. Shape the wires’ ends into hooks, then remove the central silver terminal block screw and take the neutral ground wire from the screw on the lower left, as shown.
It is not recommended to leave it under your washer after installation as it could cause vibration or noises. For common questions, refer to the following FAQs to ensure a smooth installation process for your washing machine. Due to the impact of COVID‑19, delivery times may be longer than usual and some products may be out of stock. Carefully slide your dryer back into the desired location, guiding it to avoid causing kinks in the venting. Adjust the dryer until the venting is as straight and sturdy as possible. Small amounts of trapped lint in dryer venting are inevitable, so it’s best to get a fresh start by removing build-up to help enhance your dryer’s performance.
Strip 31/2″ of outer covering from end of cable. Strip insulation back 1″ . If using 3-wire cable with ground wire, cut bare wire even with outer covering. Direct wire cable must have 5 ft (1.52 m) of extra length so dryer may be moved if needed.
Reinstall the door strike and cosmetic screw on the opposite side of dryer door opening from where they were removed. For normal dryer use, it is not suggested to remove the dryer door. However, if removal is necessary, make sure the dryer is off and cool. Open shut-off valve in supply line; valve is open when handle is parallel to gas pipe. Then, test all connections by brushing on an approved noncorrosive leak-detection solution.
Step 5: Install the vent system
Cut a hole, there may already be an indent for such an orientation. After that, you just move the internal hose and its mounting. The cut out can be used as a filler to mostly hide the old hole when riveted or screwed to a larger back piece. Use auto-body filler to fill any gaps prior to repainting the old hole area. Exhaust vents in mobile homes must be securely fastened to a flame resistant portion of the home and the vent’s ending should be outside the structure itself. If there is an extra part, go back through the steps to see what was skipped.
Starting from indoors, insert the brush a few inches and spin, then remove the brush and clean off the bristles. If you’re laying original ductwork, contact a professional for more information about choosing a location for the vent hood opening and the best ducting to help get you there. Watch as Maytag®appliance www.hookupinsiders.com/asiandate-review experts walk you through how to install laundry pedestals. Next, check to make sure your dryer is balanced using your level. Be sure to check that your dryer is level by placing the level both side-to-side and front-to-back on top of your dryer. Once your dryer is level and in place, it’s ready to use.